M A C H I N E R Y
EXTRUDERS
Conical Twin Screw Extruders
ONYX conical twin screw extruders contain some of the most state of the art equipment. It's special gear box was designed and built with the highest standards in mind. It's Helical gears are made from 20CrMnTi steel, and have been heat treated and polished. SKF thrust bearings, QT200 Gear boxes and 40 Cr Axels ensure long life and durability. The system is fully lubricated with circular gear old, and it's screw and barrel are made from 38CrMoA1A steel, which has been nitrated, polished and treated to 0.6-1.0 depth. Frequency control of the AC Motor allow it to gain considerable accuracy and a longer life span. All parts come EU and CSA approved and come with Siemens, ABB and Schneider Components.
Specifications:
Model
Diameter (mm)
Speed (rpm)
Screw Length (mm) *
Power (kw)
Heaters (kw)
Output (kg/h)
Net Weight (kg)
ONYX TE-45/90
45/90
1-45.5
989
15
11.5
40-60
3000
ONYX TE-55/110
55/110
1-30
1200
22
18
80-140
3500
ONYX TE-65/120
65/120
1-30
1440
37
24
200-250
4000
ONYX TE-65/132
65/132
1-34.7
1440
37
24
250-300
4000
ONYX TE-80/156
80/156
1-36.9
1800
55
36
320-450
5000
ONYX TE-92/188
92/188
1-32.9
2500
90
88
500-600
10000
* All conical screws are counter rotating
Parallel Twin Screw Extruders
Both the screw and barrel of ONYX's parallel twin screw extruders were designed using the building block principle. The screw configuration, barrel setup, screw L/D, number of feeding & venting protocols, screen changes, granulating methods and electrical controls are optimally adjusted according to the material properties and process requirements. The closely intermeshed screw elements have excellent self-wiping characteristics, and can be easily interchanged with others. Screw elements are inserted into a spline shaft to achieve higher torque and higher screw channel volume for even higher throughput. Over 20 years of experience has been put into the development and design of the screw and software. This enables us to produce highly efficient twin screw extruders in accordance to the requirements of the specific process. To meet the increasingly demanding challenges coming for new materials and processes, we are constantly providing new types of screw elements.
Specifications:
Model
Diameter (mm)
L/D (mm)
Speed (rpm)
Power (kw)
Torque (Nm)
Output (kg/h)
ONYX TEC-25 25 32/56 600 4 30 0.5-15 ONYX TEC-36 35.6 32/64 400 11 125 40-55 600 15 115 45-75 ONYX TEC-40 41 32/64 400 22 250 64-110 ONYX TEC-52 51.4 32/64 500 45 405 135-225 ONYX TEC-65 62 32/64 400 55 620 165-275 500 75 675 225-375 ONYX TEC-75 71 32/64 400 90 1015 225-375 500 110 1005 330-550 500 132 1190 396-660 ONYX TEC-93 93 32/64 400 250 2815 750-1250 500 250 2250 750-1250
DOWNSTREAM EQUIPMENT
ONYX downstream equipment consists of a Vacuum calibrating Table, Haul-off and Cutting unit.
ONYX 240A Specifications:
Gauge Vacuum Range
-0.08 to -0.09 Mpa
Height of Die Mounting Base
890mm to 1100mm
Center of T-Die Mounting Base 320mm Vacuum Setter Travel 500mm Caterpillar Tracing Speed 0.1 to 4m/min Width and Length of Caterpillar Belt W: 240mm L: 3,000mm Caterpillar Belt Opening 140mm Saw Linear Speed 0 to 58.6 m/s Max Sawing Section 240mm x 65mm Caterpillar Power 5HP Length of Calibrator 6,000mm
